北京旌派干式血液溶漿機產品說明：
Jipad品牌Jipad-6GL干式血液溶漿機利用隔水膜袋“隔水解凍”，完全實現了血漿干式解凍的目的,解凍結束:“血漿外觀干燥，透明、無水漬，污物，標簽不會模糊、脫落”。特制熱交換系統能夠達到“快速解凍”的效果。專門設計的“搖勻系統”避免血漿內纖維蛋白凝結。“返回水設計”有利融化箱內水溫恒定無熱點。
Jipad-6GL干式血液溶漿機結構合理，緊湊，零部件經老化等特殊處理，性能穩定可靠，整機使用壽命長，不同型號的產品適合不同規模的醫院輸血科，血庫使用，并經多家醫院臨床驗證。
北京旌派干式血液溶漿機產品特點:
1. Jipad-6GL
干式血液溶漿機采用美國DS18B20和雙金屬片兩級溫控系統，超溫自動報警并切斷電源。解凍時間20分鐘±2分鐘。
2.專門設計的的“搖擺錘擊”系統，避免血漿內纖維蛋白析出。“隔水膜袋”用醫用綠色新型材料制成，無毒,無味，無毒副作用、使用壽命長。
3.水箱密封，長期不用換水，加入專用消毒劑（氯片）效果更好，節約資源減輕換水負擔。儀器對環境不會有水漬、污物溢出,保護環境和操作人員。
4.如有血漿袋破裂因有隔水膜袋包裹，不會造成過量滲漏，污染水箱及環境.
北京旌派干式血液溶漿機技術參數：
1.電源電壓：220V/50HZ
2.功率：1800W
3.可調溫度：30℃---41℃<±1℃
4.解凍袋數：1-6袋（50-200毫升血漿）
5.解凍時間：10-20min±2min
6.容量：*多12袋（200毫升血漿）
7.可調時間：1min--99.00min
8.儀器重量：29kg加水：45kg
9.外形尺寸：460X610X960(mm)
10.搖擺頻率：50次/分鐘
11.循環能力：40L
北京旌派干式血液溶漿機裝 機 方 法：
1、將壓水棒放入隔水膜袋中
2、打開儀器上面小蓋、加入干凈的自來水，*好是純凈水。（儀器可長期不用換水。使用一段時間后，在儀器工作時，提起隔水膜袋觀察水的清澈程度確定是否需要換水）
3、加水時請注意觀察蜂鳴報警聲停止，停止說明水位已加滿請停止加水，過多加水，儀器左側溢水口，會有水溢出。
4、加水過多時側面會有水溢出，這樣不會影響儀器使用，您可在側面放水閥門放出少許即可。
5、等待40-50分鐘顯示屏實際溫度顯示37度，即可將血漿放入隔水膜袋中點擊“開/關”按鈕-------OK。
6、如需要改變設定溫度、時間請參照操作手冊。
目的
建立循環水浴箱解凍新鮮冰凍血漿、普通冰凍血漿及冷沉淀標準操作規程,規范冰凍血液成分解凍操作流程,確保血液質量安全。
職責
本科室工作人員應用此操作規程,保證為臨床提供安全的血漿。
原理
冰凍血漿融化箱采用電氣控制原理,新鮮冰凍血漿、普通冰凍血漿及冷沉淀等需要在 37 一 40℃穩定溫度條件下，快速解凍防止蛋白成分析出 ,循環水溶箱可以維持穩定溫度的水 浴條件，快速、批量觧凍,冰凍血液制品,確保觧凍速度和血液質量。
適用范圍
適用于循環水浴箱解凍新鮮冰凍血漿、普通冰凍血漿及冷沉淀操作。
器材與試劑
1、器材：血庫專用融漿機，血漿解凍袋
環境條件 溫度：20-27℃，溫度≤80% 七、操作程序：
1、連接進水管，排水管，接通電源；
2、打開電源開關，按“啟動"鍵，提示“缺水"狀態，擰開水龍頭開始加水，直至進水完成，“預溫"燈亮；
3、設定解凍濕度（一般設定為38℃）及解凍時間（根據解凍血漿數量確定，一般設定在16分鐘以上）；
4、待預溫完成后，水箱水位上升到工作狀態；
5、將血漿或冷沉淀從低溫冰箱中取出，去掉包裝盒，套上解凍袋，放入解凍槽中，蓋好解凍箱蓋；
6、解凍完成后，依次將血漿解凍袋取出，將血漿去掉解凍袋后放置室溫下待用；
7、如果解凍后的血漿溫度己經恢復到室溫仍未發出，應該將血漿轉移到4℃儲血冰箱內待用。
北京旌派干式血液溶漿機注意事項
1、解凍箱應使用獨立的三芯插座；
2、解凍箱上水時務必連好排水管，防止加水過量后溢水； 3、發現有破損血漿時需立即換水，并進行清洗
4、要避免血袋標簽等物品落入水箱內，以免堵塞水管，致使水循環系統癱瘓；
5、解凍箱長期不用時，應將解凍箱內的水全部排盡。
保養與維護
1、解凍箱應每周做清洗保養一次，清洗內外表面；
2、溫度校正：每年由計量部門對解凍箱進行一次溫度檢測，如發現實測溫度與顯示溫度相差0.5℃以上，應對解凍箱進行校正
Product Description:
The Jipad brand Jipad-6L dry blood plasmapheresis machine uses the water separating membrane bag to separate the water and thaw. The purpose of plasma dry thawing is completely realized. The end of thawing is: "the appearance of the plasma is dry, transparent, waterless, dirty, and the label will not be fuzzy and falling off". The special heat exchange system can achieve the effect of "fast thawing". The specially designed "shake up system" avoids fibrin condensation in the plasma. The "return water design" is favorable for the constant water temperature in the melting box without hot spot.
The Jipad-6L dry blood dissolving machine has a reasonable and compact structure. The components are treated by aging and other special treatments. The performance is stable and reliable, and the whole machine has long service life. Different types of products are suitable for different scale hospitals transfusion department, blood bank is used, and is verified by many hospitals.
Product features:
The 1. Jipad-6L dry blood plasma dissolve machine adopts the two level temperature control system of American DS18B20 and bimetallic chip, which can alarm automatically and cut off the power. The thawing time was 20 minutes and 2 minutes.
2. specially designed "swing hammer" system to avoid fibrin precipitation in the plasma. "Water diaphragm bag" is made of new medical green materials, which is non-toxic, tasteless, non-toxic side effects and long service life.
3. water tank is sealed for a long time without changing water. The effect of adding special disinfectant (chlorine tablet) is better, saving resources and reducing the burden of water exchange. The instrument does not have water stains, spillage of dirt, protection of the environment and the operator.
4. if the rupture of a plasma bag is wrapped in a membrane bag, it will not cause excessive leakage and pollute the water tank and the environment.
Technical parameters:
1. power supply voltage: 220V/50HZ
2. power: 1800W
3. adjustable temperature: 30 C ---41 C < + 1 c
4. the number of thawing bags: 1-6 bags (50-200 ml plasma)
5. thawing time: 10-20min + 2min
6. capacity: a maximum of 12 bags (200 ml of plasma)
7. adjustable time: 1min--99.00min
8. instrument weight: 29kg adding water: 45kg
9. shape size: 460X610X960 (mm)
10. swing frequency: 50 times / minute
11. cycle ability: 40L
Installation method:
1. Put the water rod in the water - proof bag
2. Open the top of the instrument and add clean tap water. It is best to clean water. (the instrument can not change water for a long time. After working for a period of time, in the work of the instrument, the clarity of water in the water diaphragm bag is raised to determine whether the water is needed for water exchange.
3, when you add water, please observe the stop of the beep alarm, stop indicating that the water level has been filled, stop adding water, add too much water, and the overflow on the left side of the instrument will overflow the water.
4, when the water is overloaded, there will be water overflow, which will not affect the use of the instrument, you can release a little on the side of the water valve.
5, waiting for 40-50 minutes to display the actual temperature of the display 37 degrees, you can put the plasma into the water septum bag and click "open / close" button -------OK.
6, if you need to change the setting temperature and time, please refer to the operation manual.
I. purpose
Establish standard operation procedures for circulating frozen water tank, thawing fresh frozen plasma, ordinary frozen plasma and cold precipitation, and standardize the operation process of frozen blood components, so as to ensure the quality and safety of blood.
Two. Responsibilities
The staff in this department use this procedure to ensure the safety of plasma in the clinic.
Three. Principle
Frozen plasma melting box adopts the principle of electrical control, fresh frozen plasma, ordinary frozen plasma need to be in a stable temperature 37 to 40 DEG C, rapid thawing to prevent protein precipitation, circulating water soluble box can maintain stable temperature of water bath, fast and batch frozen frozen blood products, explanation, to ensure that the explanation of freezing the speed and quality of blood.
Four. Scope of application
It is suitable for the defrosting of fresh frozen plasma, common frozen plasma and cold precipitation.
Five, equipment and reagents
1. Equipment: a special thawing machine for blood bank, a plasma thawing bag
Six, the environmental conditions of temperature: 20-27 degrees, the temperature is less than or equal to 80%, seven operating procedures:
1, connect the inlet pipe, drain pipe, connect the power supply;
2, open the power switch, press "start" key, prompt "water shortage" state, turn off the faucet start adding water, until the water is completed, "pre temperature" light;
3, set the thawing humidity (generally set to 38) and thawing time (according to the number of thawing plasma is determined, generally set at more than 16 minutes);
4. When the temperature is finished, the water level of the water tank rises to the working state.
5. Remove the plasma or cold precipitation from the cryogenic refrigerator, remove the packing box, set the thawing bag, put it in the thawing tank, and cover the thawing box cover.
6. After the defrosting is completed, the plasma thawing bag is taken out in turn, and the plasma is removed after the defrosting bag is placed at room temperature.
7, if the plasma temperature after thawing has not been released to room temperature, the plasma should be transferred to 4 centigrade to be used in the blood storage refrigerator.
Eight. Precautions
1. An independent three core socket should be used in the thawing box.
2, when the thawing box is on the water, be sure to connect the drain pipe to prevent overflowing water. 3, when the damaged plasma is found, water should be changed immediately and cleaned.
4, to avoid the blood bag label and other articles fall into the water tank, so as to avoid blocking the water pipe, causing the water circulation system to be paralyzed.
5. When the thawing box is not used for a long time, all the water in the thawing box should be exhausted.
Nine, maintenance and maintenance
1, the thawing box should be cleaned and maintained once a week, and the inside and outside surface should be cleaned.
2, temperature correction: once a year, the temperature measurement of the thawing box is carried out by the Metrology Department. If we find the difference between the measured temperature and the display temperature is more than 0.5 degrees, we should adjust the thawing box.
